×
Unmissable deals 
Up to 15% OFF Goodyear, Kumho and more!
Tyres /  Tyre News /  Motoring /  BYD Seal U DM-i Tyre Pressure

BYD Seal U DM-i Tyre Pressure

BYD Seal U DM-i Tyre Pressure

The BYD Seal U DM-i is the plug-in hybrid version of BYD’s Seal U SUV, pairing a 1.5-litre petrol engine with electric drive and a rechargeable high-voltage battery.

UK buyers choose between the front-wheel drive 1.5 DM-i Boost and 1.5 DM-i Comfort, and the all-wheel drive 1.5 DM-i AWD Design, which adds a rear drive motor.

Whichever version you have, BYD’s UK handbook lists a single tyre size: 235/50 R19 on 19-inch wheels.

Tyre pressures usually vary by tyre size, engine and load. On the Seal U DM-i the handbook keeps it simple, with one front figure and one rear figure for every version. The catch is that the front and rear figures are different, so you can’t set all four tyres to the same pressure.

List of BYD Seal U DM-i Tyre Pressures

The figures below come from BYD’s UK right-hand drive owner’s manual for the Seal U DM-i, issued February 2026, which covers both the 2WD and 4WD versions.

Your car also carries its own tyre pressure label. The handbook says it’s on the sheet metal of the right-hand B-pillar door frame, the driver’s side on UK cars, so you’ll see it when you open the driver’s door.

The handbook doesn’t list separate fully loaded figures. If your car’s label shows anything different from the table, follow the label.

Tyre Pressure Specifications for BYD Seal U DM-i

Tyre Size Normal Load (Front) Normal Load (Rear)
235/50 R19250 kPa (2.5 bar / 36 psi) 290 kPa (2.9 bar / 42 psi)

Cold tyre pressures from the UK BYD Seal U DM-i owner’s manual (right-hand drive, 2WD and 4WD), issued February 2026. The handbook prints kPa only, so bar is kPa divided by 100 and psi is rounded to the nearest whole number.

Disclaimer: the information provided in this article is intended for reference purposes only. Tyre pressures can vary depending on wheel size, trim level, load and driving conditions. Always refer to your vehicle’s official handbook or consult BYD directly for the most accurate specifications. We accept no responsibility for any discrepancies or incorrect use of this information.

BYD Seal U DM-i Tyre Pressure Monitoring System (TPMS)

The Seal U DM-i has a direct tyre pressure monitoring system that shows each tyre’s pressure in real time. You can view it on the instrument cluster by pressing the steering wheel button and scrolling to the tyre pressure display in the driving information bar.

The handbook describes these warnings:

There’s no driver reset procedure in the handbook. After a tyre rotation or a sensor replacement, the whole system needs rematching, and BYD recommends having this done by an authorised dealer or service provider.

The system doesn’t stop the car if a pressure is wrong. The handbook advises checking the readings on the instrument cluster before every drive and not setting off if they don’t match the specified pressures.

How To Check BYD Seal U DM-i Tyre Pressure

Check the pressures when the tyres are cold. The handbook defines cold as at least three hours after the car has stopped, or after driving no more than 1.6 km (1 mile).

  1. Remove the valve cap from the first tyre.
  2. Press a tyre pressure gauge firmly onto the valve and read the figure.
  3. Add or release air until the tyre matches the handbook figure: front and rear are different on this car.
  4. Refit the valve cap and repeat on the other three tyres.

Hot tyres read higher than cold ones. If you check after a longer drive, don’t let air out to reach the cold figure, as the handbook warns this leaves the tyres underinflated.

BYD recommends checking tyre pressure monthly. Each time you do, look over the tyres for cuts, bulges and anything stuck in the tread, and check the tread depth. The wear marks inside the tread show when it has reached 1.6 mm and the tyre must be replaced.

Why Tyre Pressure Matters

According to the handbook, underinflated tyres wear unevenly, affect handling and power consumption and can overheat and leak. Overinflated tyres make the ride less comfortable and are more easily damaged on rough roads.

Keeping the Seal U DM-i’s tyres at the correct pressure gives you the balance of handling, tread life and comfort BYD intended.

Get the Right Tyres for Your BYD Seal U DM-i

Getting the BYD Seal U DM-i tyre pressure right only helps if the tyres themselves are in good shape. If yours are worn or damaged, you’ll find 235/50 R19 tyres at Blackcircles.com, with fitting at a local garage or mobile tyre fitting at your home or workplace.

Browse our full range of BYD tyres, or enter your registration below to see tyres that fit your car.

Find Tyres for Your BYD

Enter your registration and postcode to see tyres that fit your BYD, with fitting at a local garage or at home.

and
Or enter tyre size

Frequently Asked Questions

What is the correct tyre pressure for the BYD Seal U DM-i?

BYD’s UK handbook lists 250 kPa (2.5 bar / 36 psi) for the front tyres and 290 kPa (2.9 bar / 42 psi) for the rear tyres. Set them with the tyres cold.

Why are the rear tyre pressures higher than the front on the Seal U DM-i?

The handbook simply gives different front and rear figures without explaining why. Use 250 kPa (2.5 bar / 36 psi) at the front and 290 kPa (2.9 bar / 42 psi) at the rear, and don’t set all four tyres to the same figure.

Is the tyre pressure different on the AWD Design model?

No. The handbook lists the same tyre size and the same front and rear pressures for both the 2WD (Boost and Comfort) and 4WD (Design) Seal U DM-i.

Where is the tyre pressure label on the BYD Seal U DM-i?

The handbook says the tyre pressure label is on the sheet metal of the right-hand B-pillar door frame, which is the driver’s side on UK cars. Open the driver’s door to see it.

What size tyres does the BYD Seal U DM-i have?

The UK handbook lists one tyre size, 235/50 R19, for both the 2WD and AWD versions. Check the sidewall of your current tyres to confirm the load index and speed rating before ordering replacements.

What tyre pressure should I use when the car is fully loaded?

The handbook doesn’t list separate fully loaded figures for the Seal U DM-i. Check the tyre pressure label on the driver’s door frame and don’t guess a higher figure.

Do I need different tyre pressures for towing?

Yes. The handbook’s towing section tells you to adjust the tyre pressures for the extra load before towing. Read that section in full, check the tyre pressure label and ask a BYD authorised dealer if you’re unsure.

What does the tyre pressure warning light mean on the Seal U DM-i?

A steady light with a yellow pressure reading means one tyre has dropped below 85% of its standard pressure. A flashing light with a red reading means a fast air leak. A light that flashes and then stays on, with “Please check TPMS” or “---” shown, means a system fault.

How do I reset the TPMS on the BYD Seal U DM-i?

The handbook doesn’t give a driver reset. The low pressure warning cancels once the tyre is back above 90% of its standard pressure. After a tyre rotation or a sensor change, the system needs rematching, which BYD recommends an authorised dealer or service provider carries out.

Should I check tyre pressure when the tyres are hot or cold?

Cold. The handbook says to check them at least three hours after the car has stopped, or after driving no more than 1.6 km (1 mile). Hot tyres read higher, so don’t let air out to match the cold figure.

How often should I check my Seal U DM-i tyre pressures?

The handbook recommends checking tyre pressure monthly, along with tread wear and anything stuck in the tread. It also advises checking the pressures shown on the instrument cluster before each drive.

Does the BYD Seal U DM-i have a spare wheel?

The tool kit listed in the handbook includes a tyre repair kit rather than a spare wheel. The kit is for small punctures in the tread only, so call for roadside assistance for larger damage.

Buy new tyres at Blackcircles.com
Want exclusive motoring news?

Subscribe to our newsletter for the latest EV, Performance, SUV & 4x4 content

Join our mailing listSign up
Back to news

Join the conversation

We love to hear from our customers. Connect with us today and let’s start a conversation.

PayPal
Representative Example: Purchase rate: 23.9% p.a. (variable). Representative: 23.9% APR (variable). Assumed Credit Limit: £1,200

PayPal Credit and PayPal Pay in 3 are trading names of PayPal UK Ltd, 76 Upper Ground, London, SE1 9PZ. Terms and conditions apply. Credit subject to status and approval, 18+ UK residents only. PayPal Credit and PayPal Pay in 3 are a form of credit, so carefully consider whether the purchase is affordable and how you will make the repayments. PayPal Pay in 3 is not regulated by the FCA. See product terms for more details and FAQs. Learn more about PayPal Credit.  Learn more about PayPal Pay in 3.